Guest, Sign inJoin
Mullingar Town CentrePhoto: Shaun Nolan · CC BY-SA 2.0
A−Hazard risk Grade
Flood & hazards in Mullingar · EPA, GSI and OPW data

Natural hazards are few in Mullingar, with low radon, steady ground and little flood-prone housing

With an estimated 2.5% of homes above the radon reference level, among the lower shares, Mullingar grades A− for hazard risk: #64 of 321 Irish towns. Flood counts only against a town, so its share of low-lying homes earns it no credit: radon and landslide ground set the grade.

In brief

What stands out about Mullingar’s hazards

From the EPA’s radon map, Geological Survey Ireland’s landslide map, the OPW’s flood relief schemes and our estimate of low-lying homes, below.

By hazard

What Mullingar faces

Each hazard against its own yardstick; meters run from low to high on that yardstick.

Not on this page: the OPW’s official flood maps and past floods (their licence doesn’t allow reuse here: see floodinfo.ie), groundwater and surface-water flooding, coastal erosion and industrial sites.
Hazard risk Grade

Hazard risk in Mullingar: A−

Radon, landslide ground and low-lying homes, each against Irish towns, then averaged.

Radon (2.5%)Better than 63% of Irish towns
Landslide ground (0%)Better than 57% of Irish towns
Low-lying homes (0%)Not counted: it would have raised the grade

Each figure is placed among Irish towns of 1,000 or more people; the grade averages the three, so a better place on each is a better grade.

Flood counts only against a town, never for it: Mullingar’s share of low-lying homes would have raised its grade, so it isn’t counted, and radon and landslide ground set it.

Its place: #64 of 321 Irish towns.

Less sure: The low-lying figure is our estimate from ground heights and the river map, not an official flood map. It can show a town is low-lying; it can’t show a town is safe.

Low-lying homes

Few of Mullingar’s homes stand low by a big river, lake or the sea

Low-lying homes, a TownRatings estimate from OPW and Geological Survey Ireland LiDAR ground heights and the EPA’s river map: not an official flood map. Smaller streams, drains and groundwater aren’t in this measure, so a low figure doesn’t mean a town never floods.

By a river, lake or estuary0%of homes within 5 m of the water’s level
Near the sea0%of homes below 4 m, within 2 km of the sea
Measured in detail100%of homes on detailed ground heights
Where Mullingar sits among 231 Irish towns
43%NoneMullingar
6%Under 0.5%
4%0.5–1%
7%1–2%
8%2–5%
6%5–10%
8%10–20%
18%20% +

Share of each town’s homes standing low by big water, for the towns measured in detail. 43% have none; Mullingar has more than 21% of them.

Towns its size: 6th of 40, from the fewest low-lying homes
#TownPeopleLow-lying
1Naas Kildare26,1800%
2Blanchardstown Dublin24,6130%
3Jobstown Dublin23,4370%
4Stepaside Dublin22,7960%
5Clondalkin Dublin22,7880%
6Mullingar Westmeath22,6670%
7Rathmines West Dublin22,6670%
8Clonsilla Dublin22,5100%
…
39Ennis Clare27,92344%
40Sandymount Dublin22,34086%

The 40 Irish towns nearest its size that are measured in detail.

7,430
homes counted
0
homes standing low by big water
11%
County Westmeath’s median
0.7%
median of Irish towns

Homes: OpenStreetMap buildings of 30 m² or more, not tagged as non-residential, in the town’s Census 2022 Small Areas. Heights: GSI Open Topographic Data LiDAR (OPW, TII and GSI surveys). Water: EPA river network (rivers of Strahler order 5 or more), lakes, estuaries and coastal waters.

River levels

November 2025 brought the River Brosna’s 3rd-highest day at Mullingar Pump Hse since 1977

Each winter’s highest level (October to September) at the OPW’s Mullingar Pump Hse gauge, in Mullingar, since 1977, in metres above the gauge’s zero. Nine days in ten it runs between 0.20 m and 0.42 m.

Each winter’s highest level, metres
Winter 1977–78: highest 0.43 m · 2 days above the normal rangeWinter 1978–79: highest 0.56 m · 8 days above the normal rangeWinter 1979–80: highest 0.67 m · 24 days above the normal rangeWinter 1980–81: highest 0.77 m · 13 days above the normal rangeWinter 1981–82: highest 0.54 m · 9 days above the normal rangeWinter 1982–83: highest 0.82 m · 25 days above the normal rangeWinter 1983–84: highest 0.60 m · 8 days above the normal rangeWinter 1984–85: highest 0.69 m · 14 days above the normal rangeWinter 1985–86: highest 0.83 m · 14 days above the normal rangeWinter 1986–87: highest 0.42 m · 0 days above the normal rangeWinter 1987–88: highest 0.69 m · 19 days above the normal rangeWinter 1988–89: highest 0.66 m · 43 days above the normal rangeWinter 1989–90: highest 0.69 m · 14 days above the normal rangeWinter 1990–91: highest 0.49 m · 12 days above the normal rangeWinter 1991–92: highest 0.52 m · 10 days above the normal rangeWinter 1992–93: highest 0.72 m · 59 days above the normal rangeWinter 1993–94: highest 0.72 m · 22 days above the normal rangeWinter 1994–95: highest 0.80 m · 29 days above the normal rangeWinter 1995–96: highest 0.55 m · 2 days above the normal rangeWinter 1996–97: highest 0.61 m · 23 days above the normal rangeWinter 1997–98: highest 0.63 m · 39 days above the normal rangeWinter 1998–99: highest 0.85 m · 93 days above the normal rangeWinter 1999–00: highest 0.78 m · 61 days above the normal rangeWinter 2000–01: highest 0.74 m · 9 days above the normal rangeWinter 2001–02: highest 0.69 m · 23 days above the normal rangeWinter 2002–03: highest 0.63 m · 38 days above the normal rangeWinter 2003–04: highest 0.63 m · 26 days above the normal rangeWinter 2004–05: highest 0.46 m · 1 days above the normal rangeWinter 2005–06: highest 0.61 m · 4 days above the normal rangeWinter 2006–07: highest 0.80 m · 66 days above the normal rangeWinter 2007–08: highest 0.84 m · 74 days above the normal rangeWinter 2008–09: highest 0.74 m · 91 days above the normal rangeWinter 2009–10: highest 0.95 m on 19 November 2009 · 46 days above the normal rangeWinter 2010–11: highest 0.69 m · 20 days above the normal rangeWinter 2011–12: highest 0.69 m · 37 days above the normal rangeWinter 2012–13: highest 0.83 m · 44 days above the normal rangeWinter 2013–14: highest 0.85 m · 32 days above the normal rangeWinter 2016–17: highest 0.52 m · 8 days above the normal rangeWinter 2017–18: highest 0.68 m · 9 days above the normal rangeWinter 2018–19: highest 0.87 m on 16 March 2019 · 20 days above the normal rangeWinter 2019–20: highest 0.94 m on 24 February 2020 · 56 days above the normal rangeWinter 2020–21: highest 0.82 m · 58 days above the normal rangeWinter 2021–22: highest 0.86 m on 20 February 2022 · 23 days above the normal rangeWinter 2022–23: highest 1.05 m on 28 October 2022 · 32 days above the normal rangeWinter 2023–24: highest 0.74 m · 18 days above the normal rangeWinter 2024–25: highest 0.59 m · 2 days above the normal rangeWinter 2025–26: highest 0.99 m on 12 November 2025 · 17 days above the normal range’22–23’25–26Record 1.05 m, 2022Top of normal range
1977–782025–26
The highest days on record
  • 28 October 20221.05 m
  • 27 January 20160.99 m
  • 12 November 20250.99 m
  • 19 November 20090.95 m
  • 24 February 20200.94 m
  • 16 March 20190.87 m

Since 1977 the River Brosna has run above its usual top on 1,297 days, most of them in the winters of 1998–99 and 2008–09.

Measured by its highest day, last winter (2025–26) was the 2nd-highest of the 47 on record here.

Source: OPW Hydro-Data (waterlevel.ie/hydro-data), Mullingar Pump Hse gauge (station 25050): daily maximum and mean levels, inspected and provisional data. The usual range is the 5th to 95th percentile of daily means, worked out by TownRatings. Live levels are on waterlevel.ie.

Warnings

Weather and flood warnings for Mullingar

Where to see the warnings in force, and what this page can’t count.

Met Éireann issues yellow, orange and red warnings for rain, wind and coastal flooding county by county; Mullingar is covered by County Westmeath’s.

WarningWhat Met Éireann means by it
YellowWeather that isn’t unusual but can be dangerous in places: be aware.
OrangeInfrequent, dangerous weather that can put people and property at risk: be prepared.
RedRare, extremely dangerous weather: take action to protect yourself and your property.

Met Éireann doesn’t publish an open archive of past warnings, so how often warnings have covered Mullingar can’t be counted here.

Met Éireann warnings · OPW river levels (waterlevel.ie)

Flood scheme

The Mullingar Flood Relief Scheme protects part of Mullingar

The Office of Public Works’ completed flood relief schemes and the areas each one benefits (OPW open data, CC BY 4.0).

Designed for
1 in 100 years
the flood it is built to hold back
Homes behind it
0.2%
in the area the Mullingar Flood Relief Scheme protects
Schemes
1
Mullingar Flood Relief Scheme
Protected places in the county
1
across County Westmeath, this town included

A scheme lowers the chance of flooding behind it; it doesn’t remove it. The low-lying figure counts homes behind defences too, so a defended town can still show a high share.

No OPW flood relief scheme protects homes anywhere else across County Westmeath.

The protected places nearest here
TownSchemeDesigned forHomes behind itAway
Mullingar WestmeathMullingar Flood Relief Scheme1 in 1000.2%–
Tullamore OffalyTullamore Flood Relief Scheme1 in 1002.4%29 km
Celbridge KildareShinkeen Stream (Hazelhatch) Flood Relief Scheme1 in 1002.6%57 km
Dunboyne MeathRiver Tolka (Clonee and Dunboyne) Scheme1 in 10014%59 km
Clonee MeathRiver Tolka (Clonee and Dunboyne) Scheme1 in 10057%61 km
Ballinasloe GalwayBallinasloe (Derrymullen) Flood Relief Scheme1 in 1003.2%62 km

Official flood maps and past floods: floodinfo.ie

Landslides

No home in Mullingar stands on landslide-prone ground

Geological Survey Ireland’s landslide susceptibility map (1:50,000), read at every home.

Homes on ground rated high or moderately high

MullingarCounty Westmeath’s medianmedian of Irish towns
High or moderately high0%
0%5%

Mullingar is among the 64% of Irish towns with no home on such ground.

GSI rates ground from low to high by its slope, soil and rock. Most Irish landslides are on steep upland slopes and peat after heavy rain; a town on flat ground has almost none.

High means the ground could slide under the right conditions, such as days of heavy rain on a steep, wet slope; it isn’t a forecast that it will.

GSI landslide susceptibility, high and moderately high classes, share of the town’s homes on mapped ground (CC BY 4.0).

Radon

An estimated 2.5% of Mullingar’s homes are above the radon reference level

The EPA’s radon map: for each 10 km square, the estimated share of homes above the national reference level of 200 Bq/m³.

1.9% of homes estimated above the reference level · 1–5% of homes4.6% of homes estimated above the reference level · 1–5% of homes0% of homes estimated above the reference level · Under 1% of homes14% of homes estimated above the reference level · 10–20% (High Radon Area)1.7% of homes estimated above the reference level · 1–5% of homes21% of homes estimated above the reference level · Over 20% (High Radon Area)1.3% of homes estimated above the reference level · 1–5% of homes11% of homes estimated above the reference level · 10–20% (High Radon Area)3.2% of homes estimated above the reference level · 1–5% of homes2.5% of homes estimated above the reference level · 1–5% of homes18% of homes estimated above the reference level · 10–20% (High Radon Area)8.9% of homes estimated above the reference level · 5–10% of homes© OpenStreetMap contributors · EPA
Under 1% of homes1–5% of homes5–10% of homes10–20% (High Radon Area)Over 20% (High Radon Area)
Share of Irish towns in each band
Under 1% of homes17%
1–5% of homes · Mullingar38%
5–10% of homes26%
10–20% (High Radon Area)11%
Over 20% (High Radon Area)9%

A square where 10% or more of homes are estimated above the reference level is a High Radon Area; 0% of Mullingar’s homes are in one. The map is an estimate by area: two neighbouring houses can differ a lot.

0%
of homes in a High Radon Area
2%
County Westmeath’s median
4%
median of Irish towns

A test is the only way to know a home’s level: two detectors, left for three months in a living room and a bedroom.

EPA radon map of Ireland (10 km grid), averaged over the town’s homes (CC BY 4.0).

Industrial sites

5 EPA-licensed sites lie inside Mullingar

Factories, farms, power plants and waste sites that hold an EPA licence for their emissions, in Mullingar and around its centre.

5
licensed sites inside Mullingar
6
licensed sites within 5 km of the centre
0.2 km
to the nearest: Soltec (Ireland) Limited
The 8 nearest licensed sites
SiteLicence and activityAway
Soltec (Ireland) LimitedIndustrial Emissions licence · wasteinside
Data Packaging Ltd.Industrial Emissions licenceinside
Penn Racquet Sports Co. (Ireland)IPC licenceinside
Mulleady’s Limited (Mullingar)Industrial Emissions licence · wasteinside
Soltec (Ireland) LimitedIndustrial Emissions licence · wasteinside
Marlinstown LandfillWaste licence3.5 km
Clondrisse Pig Farm Limited (kockdrin)Industrial Emissions licence · intensive farming6.1 km
Clondrisse Pig Farm Limited (Clondrisse)Industrial Emissions licence · intensive farming9.0 km
What the 8 licensed sites within 10 km do
ActivitySites
Waste4
Not classed in the register2
Intensive farming2

Within 5 km: 4 under Industrial Emissions licences, one under an older IPC licence and one waste facility.

An EPA licence sets what a site may release to air, water and land; it doesn’t mark the site as an accident hazard.

Sites holding dangerous substances in bulk come under the COMAH (Seveso) rules, but the HSA’s list of them has no open licence, so upper- and lower-tier sites aren’t counted here.

Source: EPA registers of Industrial Emissions, IPC and waste licences, sites licensed on 31 October 2026; distances in a straight line from the town’s centre.

Neighbours

Hazards in the places around Mullingar

Low-lying homes, radon and landslide ground, town by town.

RochfortbridgeKillucan-RathwireKinnegadCastlepollardRochfortbridgeKillucan-RathwireKinnegadCastlepollardMullingar
TownLow-lyingRadonLandslides
Mullingar0%2.5%0%
Rochfortbridge
1,498 · 12 km
–3.2%0%
Killucan-Rathwire
1,574 · 14 km
–8.9%0%
Kinnegad
3,064 · 18 km
–1.5%0%
Castlepollard
1,349 · 18 km
–26%0%

A dash under Low-lying: not measured there (too few homes with detailed ground heights), not none.

Be ready

Get ready for what Mullingar faces

What to do, and what to ask before you move.

When the river rises
  • Never walk or drive through floodwater: 30 cm of moving water can float a car.
  • Move valuables, papers and medicines upstairs.
  • Turn off gas, electricity and water if you’re told to.
Met Éireann warnings · floodinfo.ie
Radon
  • Test over three months, in a living room and a bedroom.
  • Above 200 Bq/m³, a small sump and fan usually fixes it.
  • The EPA sells radon test kits at radon.ie and lists registered contractors who fix high readings.
radon.ie
When a storm is forecast
  • Bring in or tie down bins, trampolines and anything the wind can lift.
  • Keep away from coastal paths and piers while an orange or red warning is in force.
  • Charge phones and keep a torch: fallen lines are the commonest storm damage.
  • After the storm, report a fallen line to ESB Networks and keep well clear of it.
ESB Networks PowerCheck
Before you buy or rent in Mullingar
  • Ask whether the home has ever flooded, and get a buildings insurance quote before you commit: flood cover isn’t always offered.
  • Behind a completed OPW scheme? Insurers in Insurance Ireland agreed in 2014 to offer flood cover in those areas: ask for it by name.
  • Ask the seller or landlord for a radon test result, or test in your first months there.
  • Check the address on floodinfo.ie: the OPW’s flood maps and its record of past floods.
How to read these numbers

What this data can and can’t tell you

  • An estimate, not a flood map. Low-lying homes is a TownRatings modelling step: each home’s ground height from LiDAR, against the level of the nearest big river (Strahler order 5 or more), lake or estuary within 1 km, or the sea within 2 km. A home within 5 m of the water’s level, or below 4 m near the sea, counts.
  • Flood counts only one way. A high share of low-lying homes lowers the Hazard risk Grade; a low share never raises it, because defences, small streams, culverts, groundwater and flash floods don’t show in ground heights. Below the national median a town scores as the median.
  • Defences aren’t counted. Flood defences aren’t taken off: the OPW scheme that protects the most homes is shown instead, with its design standard.
  • Measured where the heights are detailed. A town is measured, and counted, only where 80% of its homes stand on LiDAR heights. Elsewhere the page says flooding isn’t measured, never that the town is dry.
  • Radon is an estimate by area. The EPA’s radon map gives the estimated share of homes above 200 Bq/m³ for each 10 km square, averaged here over the town’s homes. It says where to test, not what one house holds.
  • The sea is measured by height. Homes count as low by the sea when their ground is under 4 m and within 2 km of coastal or estuary water; waves, surges and erosion aren’t modelled.
  • Landslide ground is a map of where slides could start. GSI’s susceptibility map rates the ground itself; it doesn’t record past slides or say when one will happen.
  • Bathing water is rated season by season. The EPA classes each identified bathing water from four seasons of samples; a rating says how clean the water has been, not how safe it is to swim.
  • One town, many streets. Risk is street by street. Check a specific address on floodinfo.ie before you buy or rent.

Check any address against the OPW’s official flood maps on floodinfo.ie

Questions about flooding and hazards in Mullingar

Does Mullingar flood?

Smaller streams, drains and groundwater aren’t in that measure, so it doesn’t mean the town never floods. For a single address, the OPW’s official flood maps and past floods are on floodinfo.ie.

Is radon a problem in Mullingar?

The EPA’s map estimates that about 2.5% of homes around Mullingar are above the radon reference level of 200 Bq/m³: a lower share than in 68% of Irish towns. 0% of its homes are in a High Radon Area. The only way to know a house is a three-month test.

Is Mullingar at risk of landslides?

No home in Mullingar stands on ground rated high or moderately high for landslides.

Is Mullingar at risk from the sea?

None of Mullingar’s homes stands below 4 m within 2 km of the sea, so the sea plays no part in its share of low-lying homes; 0% stand low by rivers, lakes and estuaries.

How does Mullingar compare with the places around it?

Radon estimates around Mullingar run from 1.5% in Kinnegad to 26% in Castlepollard; Mullingar’s own is 2.5%.

Where is the nearest bathing water to Mullingar?

Portnashangan, Lough Owel, 5.9 km away, was rated excellent for the 2025 season; 2 identified bathing waters lie within 15 km.

How is Mullingar’s Hazard risk Grade worked out?

Mullingar grades A−: radon, landslide ground and low-lying homes are each placed among Irish towns, and the grade averages them.

Flood: TownRatings’ estimate from ground heights, not an official flood map. Contains Irish Public Sector Data (Geological Survey Ireland, the Office of Public Works and the EPA) licensed under CC BY 4.0; Copernicus DEM © DLR e.V. and © Airbus, provided under COPERNICUS by the EU and ESA; © OpenStreetMap contributors. Radon and bathing water: EPA (CC BY 4.0). Landslide susceptibility: Geological Survey Ireland (CC BY 4.0).

Sources: low-lying homes: TownRatings’ estimate from GSI and OPW LiDAR, Copernicus GLO-30 and the EPA river network · radon: EPA radon map · landslides: GSI landslide susceptibility · flood schemes: OPW flood relief scheme benefiting areas · bathing water: EPA bathing water quality · river levels: OPW Hydro-Data (waterlevel.ie/hydro-data) · industrial sites: EPA licence registers · the grade: TownRatings, from these figures. Under Creative Commons Attribution 4.0 (CC BY 4.0).

Contains Central Statistics Office (CSO) data, Census 2022, and Tailte Éireann boundaries (CSO Urban Areas, Small Areas, local electoral areas, constituencies), under Creative Commons Attribution 4.0 (CC BY 4.0).